Exactly How to Set up a Bathtub
Exactly How to Set up a Bathtub
Blog Article
The content in the next paragraphs in relation to Installing A Bathtub is highly fascinating. Read on and draw your own assumptions.
Installing a bathtub isn't precisely brain surgery, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the job can move rapidly; if you need to open up a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to consider employing one before you start. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you set up a new tub in your restroom if you have already bought a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipelines.
Your devices and also product checklist ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, place the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water supply and inspect all joints as well as brand-new pipework for leaks as well as tighten them if required. Load the bathtub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bath tub needs to wait until the bathtub has been made use of at the very least once as this will settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in location in between the faucet as well as the sink. Secure the tap in position with the supplier given backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type needs to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can split fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is a good idea to fit the tiles utilizing waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that article on Installing A Bathtub from a good friend on our other web property. Are you aware of another individual who is interested by the niche? Feel free to promote it. Thank you for your time spent reading it.
Schedule A Service
Report this page